TVS electronic Printer RP 35 User Manual

MODEL : Jus’ Bill RP-35  
Mini Dot Impact Printer  
All specifications are subject to change without notice  
 
Table of Contents  
1. Features  
3
4
2. Specification  
3. Self Test  
6
4. User Switches  
7
5. Command List  
8
5.1. EMULATION EPSON TM-U200  
5.2. EMULATION CITIZEN iDP-3540  
5.3. EMULATION STAR SP200  
6. Interface  
8
9
10  
11  
11  
13  
14  
15  
6.1. Interface Connector  
7. Cash Drawer Connector  
8. Electrical Specifications  
9. Dip Switch Settings  
2
 
1. Features  
Dip Switch Configuration  
Emulation mode, communications mode, baud rate, serial/parallel handshake, and head printing  
characteristics are all configured through dip switch settings.  
Data Buffer  
The Jus' Bill RP-35 printer has a built-in 16 Kilobyte I/O buffer allowing the host computer to free itself  
after sending the print data.  
Reliable communications  
The Jus' Bill RP-35 supports multiple baud rates, protocols, and handshaking on its parallel & serial  
interfaces.  
User controls  
A power switch, a paper feed switch, power LED and Paper Low/Out error LED provide ease of use.  
Self Test Mode  
A comprehensive self-test mode is available which describes the printer configuration and dip switch  
setting information along with the version number of firmware installed.  
Print orientation  
The printer is capable of printing normal and upside down, the print orientation is selected by software  
commands.  
Selectable international characters  
The Jus' Bill RP-35 supports international characters selectable by software control.  
Multiple Fonts/Sizes  
Two different resident fonts are available for printing diversity. Each of these fonts can be printed in  
normal, double wide, double height, and quadruple sizes. Both fonts and sizes are software selected.  
Bit image graphic  
Two formats for bit mapped graphics are provided.  
Error detection  
The Jus' Bill RP-35 can detect paper-out and paper-jam as well as paper near-end, controller malfunction,  
and cover open status.  
Peripheral Drive  
Two cash drawer drivers are provided.  
Certification  
(1) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions:  
1) this device may not cause harmful interference , and  
2) this device must accept any interference received , including interference that may cause  
undesired operation.  
(2) UL/cUL (UL 60950-1)  
(3) MIC  
(4) CE-EMCD (CE-EMCD Class B should use Parallel shield Cable complied with IEEE-1284 standards)  
(5) RoHS (TUV)  
(6) CCC  
3
 
2. Specification  
Printer Specifications  
MODEL  
Jus' Bill RP-35  
PRINT METHOD  
PRINT DIRECTION  
NO. OF COLUMNS  
9-pin serial impact dot matrix  
Bi-directional (with logical seeking)  
Epson Mode : 42/35, 40/33, Star Sp200 : 42/35  
Other Modes : 40/32  
7 x 9, 9 x 9 dots  
FONT SIZE  
LINE SPACING  
PRINTING WIDTH  
PRINT SPEED  
INK RIBBON  
n/144 inch  
63.5mm (2.5”)  
5 Line / Sec (at 40 cpl)  
EPSON, ERC-38 compatible  
Black or Purple, Black/Red  
Roll Paper  
PAPER  
Media  
Width  
76.2mm (3.0”)  
Diameter  
76mm (3.0”) max.  
3-ply max. (0.2mm or 0.008” thick)  
One Original and one copy  
Copies  
DATA BUFFER  
16K bytes  
CASH DRAWER DRIVER  
2 circuits (24V, 1A max)  
RS-232C Serial (25Pin)  
USB  
USB Combo  
Ethernet  
INTERFACE  
Wireless Lan  
Centronics Parallel (36Pin)  
EMULATION  
Epson TM-U200, Citizen iDP-3540  
Star SP200  
POWER SUPPLY  
Type  
External Adaptor  
Input  
120VAC, 230VAC  
Output  
24VDC X 2.5A  
OPERATING CONDITION  
STORAGE CONDITION  
5°C to 40°C, 10% to 80% RH  
-20°C to 60°C, 5% to 95% RH  
18 million lines  
RELIABILITY  
DIMENSIONS  
WEIGHT  
MCBF  
Printhead  
Cutter  
150 million characters  
157(W) X 245.12(D) X 153.1(H)mm  
157(W) X 245.12(D) X 153.1(H)mm  
5.24 lbs (2.38 kg)  
Non cutter  
Cutter  
Non cutter  
4.96 lbs (2.25 kg)  
4
 
Overall dimension  
5
 
3. Self Test  
While pressing the paper feed switch for more than 10 seconds after the printer in turned on, the self  
test mode is initiated.  
The printer self test includes a listing of the current default settings, read and write test of internal RAM,  
checksum test of internal program memory, loop back detection statement, a staggered dot line, a few  
lines of rotating character set, and a diagnostic report.  
The printer then enters into the On-Line mode.  
Configuration Setup  
When the paper FEED switch is pressed and released instantly as the power is applied to the printer, the  
printer will print the current printer configuration settings along with the DIP switch information.  
If the printer setup needs to be changed, turn the Power Off before changing the setting.  
The printer will be setup at the factory as follows;  
Printer is setup as follows:  
Model :  
Jus' Bill RP-35  
Ver X.XX  
Serial  
Epson TM-U200  
CR=CR only  
DTR/DSR  
Firmware :  
Interface :  
Emulation :  
CR Character :  
Flow Control :  
Data Bits :  
Parity :  
8 Bits  
None  
Baud Rate :  
CPL :  
Two Color :  
Auto Cutter :  
Journal :  
9600  
40/33 Char / Line  
Installed  
Installed / Not Installed  
Installed / Not Installed  
6
 
4. User Switches  
Panel Switches  
Paper Feed button : Pressing the PF button momentarily will advance the paper one character line and  
pressing it continuously will cause a fast feed at 15 lines per second.  
Power Switch  
A Power switch located on the lower left side of the printer is used to turn the printer on/off.  
Indicators  
This section explains the different patterns signaled by the two LED indicators located on the top cover  
of the Jus' Bill RP-35.  
LED1  
GREEN  
OFF  
Flash  
ON  
LED2  
RED  
OFF  
ON  
LED3  
RED  
OFF  
ON  
STATUS  
REMARKS  
Power Off  
Power On  
On line  
Normal power is not supplied to the printer  
Normal power is supplied to the printer  
Normal error-free mode  
OFF  
OFF  
Flash  
Flash  
OFF  
ON  
OFF  
ON  
Paper low  
Cover open  
Paper empty  
ON  
Insert new paper roll  
ON  
OFF  
OFF  
Close cover  
ON  
Insert new paper roll  
ON  
Paper jam  
Test mode  
OFF  
OFF  
Impossible to recover  
Ignored Paper Low  
OFF  
ON  
ON  
7
 
5. Command List  
5.1. EMULATION EPSON TM-U200  
Command  
HT  
Hex Code  
<09>H  
Description  
Horizontal tab  
LF  
<0A>H  
Print and line feed  
CR  
<0D>H  
Carriage Return  
DLE EOT  
DLE ENQ  
ESC SP  
ESC !  
ESC %  
ESC &  
ESC *  
ESC -  
ESC 2  
ESC 3  
ESC <  
ESC =  
ESC ?  
ESC @  
ESC D  
ESC E  
ESC G  
ESC J  
ESC R  
ESC U  
ESC a  
ESC c 4  
ESC c 5  
ESC d  
ESC p  
ESC t  
<10>H<04>H<n>  
<10>H<05>H<n>  
<1B>H<20>H<n>  
<1B>H<21>H<n>  
<1B>H<25>H<n>S  
<1B>H<26>H  
<1B>H<2A>H  
<1B>H<2D><n>  
<1B>H<32>H  
<1B>H<33>H<n>  
<1B>H<3C>H  
<1B>H<3D>H<n>  
<1B>H<3F>H<n>  
<1B>H<40>H  
<1B>H<44>H<n>  
<1B>H<45>H<n>  
<1B>H<47>H<n>  
<1B>H<4A>H<n>  
<1B>H<52>H<n>  
<1B>H<55>H<n>  
<1B>H<61>H<n>  
<1B>H<63>H<34>H<n>  
<1B>H<63>H<35>H<n>  
<1B>H<64>H<n>  
<1B>H<70>H  
<1B>H<74>H<n>  
<1B>H<7B>H<n>  
<1D>H<49>H<n>  
<1D>H<61>H<n>  
<1D>H<72>H<n>  
Real-time status transmission  
Real-time request to printer  
Set right-side character spacing  
Set print mode  
Select/cancel user-defined character set  
Define user-defined characters  
Select bit-image mode  
Turn on/off underline mode  
Select 1/6 inch line spacing  
Set line spacing  
Return home  
Select peripheral device  
Cancel user-defined characters  
Initialize printer  
Set horizontal tab positions  
Turn on/off emphasized mode  
Turn on/off double-strike mode  
Print and feed paper  
Select an international character set  
Turns on/off unidirectional printing mode  
Select justification  
Select paper sensor to stop printing  
Enable/disable panel button  
Print and feed n lines  
Generate pulse  
Select character code table  
Turn on/off upside-down printing mode  
Transmit printer ID  
Enable/disable Automatic Status Back  
Transmit status  
ESC {  
GS I  
GS a  
GS r  
8
 
5.2. EMULATION CITIZEN iDP-3540  
Command  
BEL  
CAN  
LF  
Hex Code  
<07>H  
<18>H  
<0A>H  
Description  
Drive pulse setting command for 1st drawer  
Clear data in buffer  
Paper feed  
FF  
CR  
<0C>H<n>  
<0D>H  
Paper feed n lines  
Print command  
SO  
SI  
DC1  
<0E>H  
<0F>H  
<11>H  
Select expanded character mode  
Select normal character mode  
Initial set command  
DC2  
<12>H  
Inverted print mode  
DC3  
ESC BEL  
SUB  
<13>H  
<1B>H<07>H<n>  
<1A>H  
Red color print command  
1st drawer driver command  
2nd drawer driver command  
Select underline mode  
Graphic command  
Set 1/9 inch line feed  
Set 2/9 inch line feed  
Set page length  
n line skip perforation command  
Cancel skip perforation command  
Select full-cut / partial-cut  
Form feed  
ESC -  
ESC *  
ESC 1  
ESC 2  
ESC C  
ESC N  
ESC O  
ESC P  
ESC f  
FS  
<1B>H<2D>H<n>  
<1B>H<2A>H<n>  
<1B>H<31>H  
<1B>H<32>H<n>  
<1B>H<43>H<n>  
<1B>H<4E>H<n>  
<1B>H<4F>H  
<1B>H<50>H<n>  
<1B>H<66>H  
<1C>H  
1st drawer drive command  
9
 
5.3. EMULATION STAR SP200  
Command  
BEL  
Hex Code  
<07>H  
Description  
Differed drive command A” for peripheral unit  
(Default setting)  
CAN  
LF  
CR  
SO  
SI  
<18>H  
<0A>H  
<0D>H  
<0E>H  
<0F>H  
<1C>H  
<14>H  
Cancel print data in buffer  
Line feed  
Line feed (same as LF)  
Select expanded character mode  
Cancel expanded character mode  
Immediate drive command “B” for peripheral unit 1  
Cancel expanded character mode  
FS  
DC4  
ESC BEL  
n1 n2  
Adjust drive pulse width for peripheral unit  
(Default setting)  
<1B>H<07>H<n1><n2>  
<1B>H<40>H  
ESC @  
Initialize printer  
Select 7 x 7 (Half dots) character size  
(Default setting)  
ESC M  
<1B>H<4D>H  
ESC R n  
ESC P  
<1B>H<52>H<n>  
<1B>H<50>H  
Select international character set  
Select 9 x 7 (Half dots) character size  
<1B>H<57>H<31>  
H<1B>H<57>H<1>  
<1B>H<57>H<37>  
H<1B>H<57>H<0>  
ESC W 1  
Select expanded character mode  
ESC W 0  
ESC a n  
Cancel expanded character mode  
Feed paper n lines  
<1B>H<61>H<n>  
10  
 
6. Interface  
6-1. Interface Connector  
<D-SUB 25 Female Serial>  
<Centronics Parallel>  
<USB “B” Type>  
<Ethernet>  
<USB COMBO>  
Serial Interface  
<Wi-fi>  
PIN  
SIGNAL  
TXD  
RXD  
DTR  
DSR  
I/O  
Output  
Input  
Output  
Input  
-
DESCRIPTION  
Printer transmit data line RS-232C level  
Printer receive data line RS-232C level  
Printer handshake to host line RS-232C level  
Data Send Ready  
2
3
4, 20  
6
1, 7  
GND  
System Ground  
USB Interface  
PIN  
SIGNAL  
+5V  
DATA-  
DATA+  
GND  
I/O  
DESCRIPTION  
+5V  
Printer transmit data line  
Printer transmit data line  
System Ground  
1
2
3
4
-
-
-
-
11  
 
Centronics Parallel Interface  
PIN SIGNAL  
STROBE-  
I/O  
Input  
Input/Output  
Output  
Output  
Output  
DESCRIPTION  
Synchronize signal Data received  
Data bit Transmitted 0~7  
Data receiving completed.  
Impossible to print of data receiving.  
Paper empty  
1
2~9  
10  
DATA0~7  
ACK-  
11  
BUSY  
12  
PE  
13  
14  
15  
16  
SELECT  
AUTO FEED-  
GROUND  
GROUND  
NC  
Output  
Input  
-
-
Printer status for ON/OFF line  
Paper auto feed signal  
System ground  
System ground  
17  
-
18  
19~30  
31  
LOGIC-H  
GROUND  
INIT-  
-
-
+5V  
System ground  
Initialize  
Input  
32  
33  
34  
35  
ERROR-  
GROUND  
NC  
Output  
-
-
-
Printer error  
System ground  
+5V  
+5V  
36  
SELLECT IN-  
Input  
Printer select signal  
Ethernet Interface  
PIN  
1
2
SIGNAL  
I/O  
Data Out +  
Data Out -  
GND  
Output Data +  
Output Data -  
Ground  
3
4
5
6
Data IN +  
Data IN -  
N.C  
Input Data +  
Input Data -  
7
N.C  
8
N.C  
12  
 
7. Cash Drawer Connector  
The Jus' Bill RP-35 can operate two cash drawers with a 6 pin RJ-11 modular connector. The driver is  
capable of supplying a maximum current of 1.0A for 510 ms or less, when not printing.  
<Cash Drawer Connector>  
PIN  
1
SIGNAL  
Signal GND  
DESCRIPTION  
-
2
3
4
Drawer kick-out drive signal 1  
Drawer open/close signal  
+24V  
Output  
Input  
-
5
6
Drawer kick-out drive signal 2  
Signal GND  
Output  
-
13  
 
8. Electrical Specifications  
The Jus' Bill RP-35 requires a power supply with the following parameters.  
A linear power Adapter is included in the Jus' Bill RP-35 box.  
Power Supply Voltage : 24VDC±10%  
Power Supply Current : 2.5 A  
<Power Supply Connector>  
14  
 
9. Dip Switch Settings  
This table gives the definition for the DIP switch settings.  
SW1  
Function  
Setting  
1
2
3
4
5
6
7
8
Epson TM-U200  
Epson TM-U300  
Citizen iDP3540  
Star SP200  
OFF  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
Emulation  
········  
CR  
Character  
CR=CR Only  
CR=CR + LF  
OFF  
ON  
40/33  
Char/Line  
42/35  
OFF  
ON  
CPL  
Char/Line  
Auto  
Cutter  
Not Install  
Install  
OFF  
ON  
Not Install  
Install  
OFF  
ON  
2Color  
Journal  
S
E
R
I
A
L
Not Install  
Install  
OFF  
ON  
SW2  
Function  
Setting  
1
2
3
4
5
6
7
8
Flow  
Control  
DTR/DSR  
Xon/Xoff  
OFF  
ON  
38400  
19200  
9600  
OFF  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
Baud  
Rate  
4800  
8 Bits  
7 Bits  
OFF  
ON  
Data Bits  
Parity  
None  
Odd  
-
OFF  
ON  
ON  
OFF  
ON  
Even  
Auto  
Melody  
Not Install  
Installed  
OFF  
ON  
15  
 
SW1  
Function  
Setting  
1
2
3
4
5
6
7
8
Epson TM-U200  
Epson TM-U300  
Citizen iDP3540  
Star SP200  
OFF  
OFF  
ON  
ON  
OFF  
ON  
OFF  
ON  
Emulation  
CR  
Character  
CR=CR Only  
CR=CR + LF  
OFF  
ON  
P
A
R
A
L
40/33 Char/Line  
42/35 Char/Line  
OFF  
ON  
CPL  
Auto  
Cutter  
Not Installed  
Installed  
OFF  
ON  
L
E
L
Not Installed  
Installed  
OFF  
ON  
2 Color  
Journal  
Not Installed  
Installed  
OFF  
ON  
SW2  
Function  
Setting  
1
2
3
4
5
6
7
8
Auto  
Melody  
Not Install  
Installed  
OFF  
ON  
16  
 
17  
 
Rev. 1.0  
 

Toshiba Computer Drive PX02SMB160 User Manual
Toshiba CRT Television 27A44 User Manual
Toshiba Security Camera CS3910BH User Manual
TP Link Network Router TD 8840T User Manual
Trane Air Compressor RTCA 108 216 User Manual
Triarch Indoor Furnishings 29583 User Manual
Vanguard Indoor Fireplace VMH26TNC User Manual
VDO Cyclecomputing Watch Z3 PC LINK User Manual
Viking Beverage Dispenser VCWB301 User Manual
Weber Charcoal Grill 178759 User Manual